-V- (vsze@wwdg.com)
Mon, 12 Jun 2000 14:06:37 -0700


well, usually the pin doesn't move. it's the plastic rod that breaks off
and slides on the pin (kinda hard to explain). Right now I'm working on
the ZZ but I've fixed the problem already... But I don't know if it's also
because of the scale. I only modify 1/144 kits and the surfaces tend to be
a bit small...

----- Original Message -----
From: "Kev K" <fayerocks@hotmail.com>
To: <gundam@aeug.org>
Sent: Monday, June 12, 2000 11:38 AM
Subject: Re: [gundam] modelling adhesives

> Hum.. that's very odd. I used the same methods for my MG Dom's thumb and
it
> seems to work fine. Maybe you have let it sit for a day for the adhesive
to
> cure. You said that the pin tends to slide around. You could try get a
> bigger pin or put some epoxy putty in the hole then insert the metal pin
> inside and pull it back out. It should keep the pin firm that way. Btw
> what model are you working on?? Maybe I can check and see the problem.
>
>
> >From: "-V-" <vsze@wwdg.com>
> >Reply-To: gundam@aeug.org
> >To: <gundam@aeug.org>
> >Subject: Re: [gundam] modelling adhesives
> >Date: Mon, 12 Jun 2000 11:21:36 -0700
> >
> >This is what i do usually do. However, the epoxy still breaks and the
> >plastic rod starts sliding on the pin... (this is only if i move it
around
> >excessively (i.e. transforming).
> >I went out to buy that krazy glue gel stuff and it seems to work ALOT
> >stronger than any adhesive i've used so far.
> >
> >-V-
> >
> >----- Original Message -----
> >From: "Kev K" <fayerocks@hotmail.com>
> >To: <gundam@aeug.org>
> >Sent: Monday, June 12, 2000 11:17 AM
> >Subject: Re: [gundam] modelling adhesives
> >
> >
> > > Someone in the list mentioned before, for any kind of kit
customization
> >or
> > > scratchbuilding you'll need the "pinning" method. What you do is get
a
> >pin
> > > vise and drill a small hole into both of the connecting ends of the
> > > plastics. Then insert a small metal rod or tube (can be bought in
most
> > > hobby stores) in these holes and use a touch of epoxy cement to glue
> >them.
> > > This will keep the plastic rod from breaking since it's pinned down on
> >the
> > > plastic itself. Hope that helps.
> > >
> > > >From: "-V-" <vsze@wwdg.com>
> > > >Reply-To: gundam@aeug.org
> > > >To: <gundam@aeug.org>
> > > >Subject: [gundam] modelling adhesives
> > > >Date: Sun, 11 Jun 2000 00:48:00 -0700
> > > >
> > > >For modelling people:
> > > >When doing customizing, let's say you were to make joint (or let's
say
> >you
> > > >are extending a forearm) alot of the times, you would have a _L <--
> >this
> > > >kind of a protruding thing.. (sorry, not very good explanation). But
> >after
> > > >you cut that protruding thing and extend with plastic board etc..
what
> >do
> > > >you guys use to stick the new plastic rod back on? This is usually
> > > >something I'm always stuck with and each time, it falls off. I've
> >tried
> > > >epoputty, epoxy, cement, laquer putty... but after moving it around,
> >it
> > > >will still break. (i want to keep the movement).
> > > >
> > > >V
> > >
> > >
________________________________________________________________________
> > > Get Your Private, Free E-mail from MSN Hotmail at
http://www.hotmail.com
> > >
> > >
> > > -
> > > Gundam Mailing List Archives are available at http://gundam.aeug.org/
> > >
> >
> >
> >-
> >Gundam Mailing List Archives are available at http://gundam.aeug.org/
>
> ________________________________________________________________________
> Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
>
>
> -
> Gundam Mailing List Archives are available at http://gundam.aeug.org/
>

-
Gundam Mailing List Archives are available at http://gundam.aeug.org/



This archive was generated by hypermail 2.0b3 on Tue Jun 13 2000 - 06:00:14 JST