Gus Jae (gusjae@channel1.com)
Thu, 17 Jun 1999 17:44:25 -0400


You are very welcome. You should be Ok using the Tamiya stuff, worst case,
clean it off. But you should be fine.
Good luck!
Gus Jae
gusjae@channel1.com
----- Original Message -----
From: Pedro Corzo <pcorzo@geomat-intl.com>
To: <gundam@aeug.org>
Sent: Thursday, June 17, 1999 10:53 AM
Subject: Re: [gundam] Give me a hand, in here

> Thanks I appreciate it,
>
> Now can I use my Tamiya primer with it, because in the can it says that is
> for plastic and metal?
>
> Pedro
> ----- Original Message -----
> From: Gus Jae <gusjae@channel1.com>
> To: <gundam@aeug.org>
> Sent: Thursday, June 17, 1999 10:33 AM
> Subject: Re: [gundam] Give me a hand, in here
>
>
> > ----- Original Message -----
> > From: Pedro Corzo <pcorzo@geomat-intl.com>
> > To: <gundam@aeug.org>
> > Sent: Thursday, June 17, 1999 8:01 AM
> > Subject: [gundam] Give me a hand, in here
> >
> >
> > Yesterday I posted the following questions, without any answer:
> >
> > What are the differences between these kotobukiya hand sets (extracted
> from
> > rainbow ten list)?:
> >
> > fist square finger
> > >> This is for 1/144 Z and ZZ series models. The mech designs for those
> > series, plus others, used squarish fingers. The fist looks like they
are
> > made out of blocks. Keep in mind that these are not for the smaller
> Gundams
> > like the F90s, G, W, V, and X Gundams.
> > fist round finger
> > >> Same as above, but round fingers instead. They used these for the
0080
> > and 0083 mechs.
> > palm square finger,
> > >> Same as above, this time the palm is opened.
> > 1/100 fighting TECCHAN CHOP LARGE,
> > >> This was made for the 1/100 G Gundam HG series. Should not use with
MS
> > not from the F90s, G, W, V, and X Gundams.
> > 1/144 fighting TECCHAN CHOP SMALL,
> > >> Same as above, in 1/144 scale.
> > 1/100 fighting TECCHAN FIST LARGE,
> > >> This time this is a fist for the 1/100s
> > 1/144 fighting TECCHAN FIST SMALL,
> > >> For the 1/144s.
> >
> > Hope that helps. Keep in mind that these are made of white metal
instead
> of
> > plastic or resin, and it requires a bit of work, and a different primer
> when
> > painting.
> > You will also need to rike up some joints to put then in the model's
> wrist.
> >
> > Hope that was helpful. Happy modeling!! :)
> >
> > Gus Jae
> > gusjae@channel1.com
> >
> >
> >
> > -
> > Gundam Mailing List Archives are available at http://gundam.aeug.org/
> >
>
>
> -
> Gundam Mailing List Archives are available at http://gundam.aeug.org/
>
>

-
Gundam Mailing List Archives are available at http://gundam.aeug.org/



This archive was generated by hypermail 2.0b3 on Fri Jun 18 1999 - 06:44:01 JST